3 Phase Motor With Gearbox


1. Orthogonal (Right-Angle) Output for Space-Efficient Equipment Layout
The input and output shafts are oriented at a right angle, eliminating the need for additional redirection mechanisms. This allows the drive system to be positioned in the confined spaces along the sides or at the bottom of the machine frame, simplifying the overall mechanical structure and reducing the complexity of frame design.
2. Die-Cast Aluminum Housing: Lightweight with Excellent Heat Dissipation
The housing is manufactured via aluminum alloy die-casting and features an anodized surface finish, offering superior thermal conductivity compared to cast-iron housings. It ensures stable heat dissipation during continuous light-to-medium load operations, preventing heat buildup. Furthermore, it provides enhanced rust resistance, making it well-suited for standard indoor workshop environments.
3. Multi-Faceted Mounting: Flexible Assembly in Six Orientations
The housing features a symmetrical, square-shaped design that supports six standard mounting orientations-including horizontal, vertical, and side-mounted configurations. Without requiring any structural modifications to the housing, a single unit can accommodate various mounting styles (such as B3, V5, and V6), offering high versatility for inventory management.

|
Model |
Nmrv Worm Gear Reducer |
|
Ratio |
5, 7.5, 10, 15,20, 25, 30, 40, 50, 60, 80, 100 |
|
Rated power |
0.06~15kW |
|
Output torque |
5N·m - 1800N·m
|
| Installation Method |
Horizontal, vertical, flange-mounted, hollow-shaft mounted |


NMRV gearbox structure







Installation and Maintenance Guidelines
1. Ensure that flange mating surfaces are clean, and tighten bolts evenly in a diagonal pattern. Verify the coaxial alignment between the input motor and the output load to prevent off-center loading, which accelerates wear on the worm gear.
2. The lubricating oil must be changed after the first 300–400 hours of operation to remove metal debris generated during the break-in period. Under normal operating conditions, the oil change interval is approximately 4,000 hours; this interval should be shortened in environments with high temperatures or excessive dust.
3. Do not obstruct the breather plug. A blocked breather can cause an internal pressure buildup within the housing, frequently leading to oil seal leakage. Note that the position of the breather plug varies depending on the mounting orientation; verify its correct orientation prior to installation.
4. Use only lubricants specifically designed for worm gear units. Do not substitute with standard gear oils or general-purpose machine oils. Never mix different brands or types of lubricants.
5. Regularly inspect the oil seals. Exposure to oil mist or dust accelerates the aging of oil seals; replace them promptly if leakage occurs to prevent rapid wear of the worm gear due to insufficient lubrication.
6. If the unit has been idle for more than 3 months, check the oil level before restarting. Rotate the unit manually to ensure smooth operation, and perform a no-load test run to confirm there are no irregularities before applying a load.






Q1: What is the difference between NMRV and NRV?
A1: NMRV features a direct-mount input via a motor flange, whereas NRV typically utilizes an input shaft design, requiring a separate coupling to connect to the motor-a configuration that allows customers to pair the unit with motors from various brands.
Q2: Why is the transmission efficiency of a worm gear drive lower than that of a planetary gearbox?
A2: It relies on sliding friction for meshing, which results in sliding losses; the higher the gear ratio, the lower the efficiency. Its advantages include a right-angle drive configuration, low cost, and self-locking capability. It is well-suited for intermittent operation but is not appropriate for long-term, high-power continuous use.
Q3: Can NMRV gear motors be used for frequent forward and reverse operation?
A3: Yes, they can; however, since the bronze worm gear has limited resistance to alternating impact loads, frequent reversals will accelerate wear on the gear tooth surfaces. When selecting a unit, it is recommended to increase the service factor, lower the acceleration during reversal, and minimize impact.
|
|
|
|||
|
|
||||
Hot Tags: 3 phase motor with gearbox, China 3 phase motor with gearbox manufacturers, suppliers, factory
Previous
NMRV Worm Gear ReducerYou Might Also Like
Send Inquiry

































